
The MD2134 is a high-speed source driver for use in a pulsed current waveform generator. This programmable, fast, arbitrary current level driver is designed for medical ultrasound imaging beamforming applications. It also can be used in HIFU, NDT ultrasound and other instrument applications.The MD2134 consists of CMOS digital logic input circuits, an eight-bit current DAC for aperture weighting amplitude control, and a programmable 15-level pulse amplitude modulation (PAM) current-source that does not include a zero level. The fast current sources are constructed with current-switch array, controlled by the LV0~LV15 level-register as the waveform data points. Four logic inputs M[3:0] are used for transmit data level selecting, as well as the transmitting timing control pins. Each level can be programmed to a resolution of +/-127 including zero (8-bit) in addition to an 8-bit SPI apodization DAC. The outputs PA and PB are controlled by M[3:0] pins directly, as well as the polarity-flip bit S1 in the SPI register. The high-speed SPI interface will achieve per-scan-line fast data updating for dynamically changing delay time, weighting and waveforms.The MD2134 outputs are designed to drive two very low-threshold, high-voltage depletion N-MOSFETs, such as DN2625s, as source drivers. The two DN2625 drains are connected to a center-tap RF pulse transformer. The transformer’s secondary output connects to a cable and piezoelectric or capacitive transducer as a load with a good impedance match.
Multiple-level ultrasound pulser
Fast switching current source for push-pull topology
250MHz maximum frequency, 4.0ns input to output delay
15 independent programmable output level registers
Pulse amplitude modulation (PAM) with 8-bit resolution
8-bit apodization DAC for peak output current via SPI
Very low second order harmonic distortion
Picoseconds time-jitter from input to output
Fast SPI write and read-back of level & DAC registers
+5.0V power supply, 2.5V CMOS logic interface
Drives DN2625 MOSFETs output up to 230VP-P
Programmable aperture windowing
MD2134 封裝圖
型號 | 制造商 | 描述 | 購買 |
---|---|---|---|
MD2134K7-G | - | - | 立即購買 |
我們使用的汽車正在向著綠色節能、網絡化、智能化的方向發展,車載電子設備的計算能力越來越高,作為人機界面的屏幕顯示效果越來越好,內容越來越豐富。
由于生成的md5信息中,每個md5值后都緊跟著對應的文件的路徑(可能是相對路徑),于是將生成的md5保存到某個文件中,以后可以使用該文件來檢查md5值對應文件內容是否發生了修改。
OPA2134雙列8腳封裝,寬帶為8MHz,轉換速率為20V/us,輸入失調電壓為±0.5mv,具有8nv(HZ平方根)的噪聲密度,0.00008%的失真系數和20V/us的上升速度。
OPA2134系列是超低失真,低噪聲運算放大器,為音頻應用完全指定。本文介紹了OPA2134引腳及特性,其次介紹了OPA2134封裝信息與絕對最大額定值,最后介紹了三款OPA2134的應用電路。
本文主要介紹了五款opa2134應用電路圖。0PA134系列運算amps是單位增益穩定和合適的對于音頻和通用廣泛的應用。所有電路是完全獨立的雙通道版本,保證正常的行為時,一個放大器在包裝是過載或短路。電源pins應與10nF被繞過或...
由于售貨機的功能不斷增多,售貨機控制系統也相應得不斷變得龐大,這就使原來的面向過程的開發方法變得越來難以擴展和維護,根據自動狀態機的理論,提出一種在售貨機上的狀態機模型,該模型對系統狀態進行抽象和分離...
本文通過ARM7微處理器芯片LPC2134的GPIO實現了與內藏T6963C的液晶顯示模塊的接口設計,并在軟件上實現了其基本顯示功能,從而在滿足了工程設計的要求。
隨著電力系統的發展,其系統容量越來越大,結構越來越復雜,系統中的自控及繼保裝置所需處理的信息不斷增加,這對人機接口的功能提出了更高的要求。新型的人機接口模塊要能夠
MC74HC589A | MC74VHC245 | MJD128 | MMBF4117 |
MOC3010M | MCP37231-200 | MOC206M | MC100ELT23 |
MOC211M | MIC3203-1 | MC100EL17 | MAT01 |
MCP47FEB01 | MC100EP51 | MCP2510 | MIC184 |
MC12080 | MC10H105 | MC74HC112A | MJF15031 |